雙組份涂膠機比例調節條件
時間:2017-08-23 來源:http://www.aabrs.cn/ 發布人:昌盛機械
1.雙組份打膠機的A組、B組份膠應保持清潔,嚴防異物進入膠中.
1. A group and B component glue should be kept clean and prevent foreign body from entering into glue
2.全封閉固化劑膠路系統,避免固化劑與空氣接觸而固化
2., all closed curing agent road system, to avoid curing agent and air contact and curing
3、升降系統采用手動轉閥控制,兩種組份的比例調節,可通過調整滑塊在擺動桿上的位置來改變.以上是雙組份打膠機的基本才做原理.
3. The lifting system is controlled by manual rotary valve. The proportion adjustment of the two components can be changed by adjusting the position of the slider on the swing bar
4.節約人工:用工少,機械操控一人完全可以解決。
4., save labor: less labor, mechanical control, a person can solve.
5、固化劑過濾器下端出口及混合器進料處均設有高壓球閥,沖膠泄壓用,混合器上設有單向針閥,不但使混膠更加均勻,而且防止兩種組份互竄.
5. The lower end of the stabilizer, the outlet of the filter and the mixer inlet are all equipped with high pressure ball valve, which is used for punching, releasing and pressure. The mixer is equipped with one-way needle valve, which not only makes mixing glue more uniform, but also prevents the two components from channeling each other
6、靈敏的高壓保護閥使操作和使用更安全
6 、 sensitive high pressure protection valve makes operation and use safer
7、基料泵、固化劑泵及比例泵均采用特殊的高壓柱賽泵,雙向等量供料,基料泵由液壓系統驅動,固化劑泵由氣動馬達驅動.
7, base pump, curing agent pump and proportional pump are used special high-pressure cylinder race pump, two-way equal feeding, base pump driven by hydraulic system, curing agent pump driven by pneumatic motor
8.節省場地:雙組份打膠機全套設備占地1.5×5米,可以合理的布置車間空間,有力提高車間利用率。
8., save space: two sets of glue machine, a full set of equipment covers an area of 1.5 * 5 meters, you can reasonably layout workshop space, and effectively improve the utilization rate of the workshop.
9、雙組份打膠機液壓/氣動型主要有基料泵、固化劑泵、比例泵、基料泵升降系統、調比結構、混膠結構、氣動系統、液壓系統及電氣系統組成.
9 、 two component rubber machine hydraulic / pneumatic type mainly has base pump, curing agent pump, proportional pump, base pump, lifting system, regulating structure, mixing structure, pneumatic system, hydraulic system and electrical system
二者輔以增壓供料壓盤,充分保證高黏度流體的滿腔輸送,基料壓入并增高至高壓,固化劑壓入并增壓,再送至比例泵,固化劑的流量由調比機構調節,二種組份同時送入混合器,充分混合后到達擠膠槍.
The two auxiliary booster feeding pressure plate, and fully guarantee the delivery filled with high viscosity fluid, the base material is pressed in and increased to high pressure, pressure and curing agent into the supercharger, sent to the proportional pump, curing agent flow by adjusting mechanism for adjusting the ratio of two components at the same time, into the mixer after mixing to the glue gun.
本文由雙組份打膠機為您提供,我們的網站是:http://linshi.jncsjx.com/我們將以全心全意的熱情為您提供更優質的服務,歡迎您的訪問!
This article is made up of a two piece punch press. Our website is: http://linshi.jncsjx.com/We will wholeheartedly provide you with better service, you are welcome to visit!
- 中空玻璃生產線一天能做多少平方 2024/12/23
- 全自動丁基膠涂布機操作規程 2024/12/14
- 丁基膠涂布機在使用的常見問題 2024/12/13
- 雙組份打膠機如何調整滴膠量? 2024/12/09
- 中空玻璃生產線的磨損如何解決 2024/12/07
- 雙組份打膠機對于打膠工作完成很重要 2024/12/05
- 全自動封膠線的工業自動化設備介紹 2024/12/03
- 玻璃涂布機設備:設備存在的安全隱患 2024/11/25
- 中空玻璃加工設備:玻璃開膠的應急處理措施 2024/11/21
- 中空玻璃生產線:玻璃起霧怎么辦?昌盛為您解決! 2024/11/20