丁基膠涂膠機的操作要注意什么?
時間:2023-07-07 來源:http://www.aabrs.cn/ 發布人:昌盛機械
1. 準備工作:將需要涂布的鋁隔條準備好,檢查涂布機的各項參數是否正常。
1. Preparation: prepare the aluminum spacer strip to be coated, and check whether the parameters of the coating machine are normal.
2. 調整設備:根據需要調整涂布機的涂布速度、壓力和溫度等參數,確保涂布質量符合要求。
2. Adjusting equipment: Adjust the coating speed, pressure, and temperature parameters of the coating machine as needed to ensure that the coating quality meets the requirements.
3. 丁基膠涂布機在常溫下呈固體形態,須經過110-150℃得高溫才能融化使用,因丁基膠導熱較慢須加熱20-30分鐘(視氣溫而定)才能完全融化,所以要求每次使用該機之前要加熱膠缸、膠頭(110-150℃下保溫)待膠融化后才能進行工作 。
3. The butyl adhesive coating machine is in a solid form at room temperature and must undergo a high temperature of 110-150 ℃ before melting. Due to the slow thermal conductivity of the butyl adhesive, it needs to be heated for 20-30 minutes (depending on the temperature) to fully melt. Therefore, it is required to heat the rubber cylinder and head (insulated at 110-150 ℃) before each use of the machine before starting work.
4. 監控涂布質量:丁基膠絕對不能出現斷膠,鋁條露白,這是影響中空玻璃壽命的關健。確保涂布的均勻性和厚度符合要求。
4. Monitoring the coating quality: The butyl adhesive must not break or the aluminum strip is exposed, which is a key factor affecting the lifespan of the insulating glass. Ensure that the uniformity and thickness of the coating meet the requirements.
5. 完成涂布:涂布完成后,關閉涂布機的開關,清理涂布機的殘留物和廢料,保持涂布機的清潔。
5. Complete coating: After the coating is completed, turn off the switch of the coating machine, clean the residue and waste of the coating machine, and maintain the cleanliness of the coating machine.
上一篇:中空玻璃全自動封膠線的的使用優勢
下一篇:全自動鋁條折彎機使用優勢
相關新聞 moer+
- 中空玻璃生產線一天能做多少平方 2024/12/23
- 全自動丁基膠涂布機操作規程 2024/12/14
- 丁基膠涂布機在使用的常見問題 2024/12/13
- 雙組份打膠機如何調整滴膠量? 2024/12/09
- 中空玻璃生產線的磨損如何解決 2024/12/07
- 雙組份打膠機對于打膠工作完成很重要 2024/12/05
- 全自動封膠線的工業自動化設備介紹 2024/12/03
- 玻璃涂布機設備:設備存在的安全隱患 2024/11/25
- 中空玻璃加工設備:玻璃開膠的應急處理措施 2024/11/21
- 中空玻璃生產線:玻璃起霧怎么辦?昌盛為您解決! 2024/11/20