一、雙組份打膠機的基本操作原理

　　First, the basic operation principle of two component gluing machine

　　1. 固化劑過濾器下端出口及混合器進料處均設有高壓球閥，沖膠泄壓用，混合器上設有單向針閥，不但使混膠更加均勻，而且防止兩種組份互竄。

　　The 1. curing agent, the lower end of the filter and the mixer inlet are all provided with a high pressure ball valve, which is used for punching and releasing pressure. The mixer is provided with one-way needle valve, which not only makes the mixing glue more uniform, but also prevents the two components from channeling each other.

　　2、基料泵、固化劑泵及比例泵均采用特殊的高壓柱賽泵，雙向等量供料，基料泵由液壓系統驅動，固化劑泵由氣動馬達驅動。二者輔以增壓供料壓盤，充分保證高黏度流體的滿腔輸送，基料壓入并增高至高壓，固化劑壓入并增壓，再送至比例泵，固化劑的流量由調比機構調節，二種組份同時送入混合器，充分混合后到達擠膠槍。

　　2, base pump, curing agent pump and proportional pump are used special high-pressure cylinder race pump, two-way equal feeding, base pump driven by the hydraulic system, curing agent pump driven by pneumatic motor. The two auxiliary booster feeding pressure plate, and fully guarantee the delivery filled with high viscosity fluid, the base material is pressed in and increased to high pressure, pressure and curing agent into the supercharger, sent to the proportional pump, curing agent flow by adjusting mechanism for adjusting the ratio of two components at the same time, into the mixer after mixing to glue gun.

　　3. 升降系統采用手動轉閥控制，兩種組份的比例調節，可通過調整滑塊在擺動桿上的位置來改變。

　　3. the lifting system is controlled by manual rotary valve, and the proportion adjustment of the two components can be changed by adjusting the position of the slider on the swing bar.

　　4.雙組份打膠機液壓/氣動型主要有基料泵、固化劑泵、比例泵、基料泵升降系統、調比結構、混膠結構、氣動系統、液壓系統及電氣系統組成。

　　4. pairs of hydraulic press / pneumatic type mainly has base pump, curing agent pump, proportional pump, base pump, lifting system, regulating structure, mixing structure, pneumatic system, hydraulic system and electrical system.

　　二、用中空玻璃打膠機時應該注意些什么以及如何操作中空玻璃打膠機

　　Two. What should we pay attention to when using a hollow glass beating machine and how to operate the insulating glass gluing machine?

　　1、混膠或沖槍時，一定要先打開膠嘴控制閥門，然后再打開供膠機，以免壓力劇增損壞設備或者出現安全事故。

　　1, mixing glue or gun, must first open plastic mouth control valve, and then open the glue machine, so as to avoid pressure surge, damage to equipment or safety incidents.

　　2、混膠或沖槍(沖洗混膠器、膠嘴)時，必須把機頭行走到軌道末端，用接膠板接住膠嘴內放出的膠，以免污染設備。

　　2, mix glue or blunt gun (rinse glue mixer, glue mouth) when, must move head to track end, use glue board to catch the glue that releases inside glue mouth, lest pollute equipment.

　　3、沖槍時先關閉機頭上的B膠出膠閥門，關閉B膠泵，然后打開B膠回流閥門，后沖槍，沖洗至出膠口不出黑膠，沖洗才能結束。

　　3, when the gun, first off the nose on the B glue out valve, turn off the B glue pump, and then open the B glue reflux valve, and finally blunt gun, rinse to the glue mouth, no black glue, rinse to finish.

　　4、操作參數設置時，在控制箱pc顯示屏上進行，根據須要而選擇設定值，不要隨意設定，以免控制器發出錯誤的信息，影響打膠質量或損壞設備。

　　4, the operation parameters are set on the control box PC display screen, according to the need to select the set value, do not arbitrarily set, so as to avoid the controller to send wrong information, affect the quality of glue or damage equipment.

　　5.機頭前方檢測玻璃開關的光眼上不能有膠，否則誤工作。

　　5. front of the nose to detect glass switch, light eye can not have glue, or else work by mistake.

　　本文由雙組份打膠機為您提供，我們的網站是:http://www.aabrs.cn/我們將以全心全意的熱情為您提供更優質的服務，歡迎您的訪問!

　　This article is made up of a two component press machine. Our website is: http://www.aabrs.cn/, we will provide you with better service with your wholehearted enthusiasm, and welcome your visit!