導致中空玻璃打膠機密封不嚴的方法
時間:2017-12-21 來源:http://www.aabrs.cn/ 發布人:昌盛機械
雙組份打膠機結構較為復雜分為電氣部分以及供膠部分購買前一定要將這些部分全部檢查完畢,以免后續出現各種故障。
The two component glue machine is complex. It is divided into electrical parts and the supply parts. All parts must be checked before they are purchased, so as to avoid any subsequent failures.
我們要檢測導軌、鋁槽、滑動軸承部分,這部分平時如果收到過撞擊等很容易變形損壞,即便是一些微小的變形也可能導致設備工作不正常如打膠機的電機時快時慢,打膠質量差等問題。
First of all we want to detect guide, aluminum groove and sliding bearing part, this part usually if the received impact is easy to deformation and damage, even a minor deformation may also lead to the electrical equipment does not work properly such as glue machine speed, such as the poor quality of glue.
檢測雙組份打膠機的供膠管路是否通暢,混交棒是否完好。因為我們使用膠體的特質決定的供膠管路非常容易杜塞,如果對方平時沒有注意對設備保養那么有很大的可能會堵塞、混交棒損壞,如果這部分損壞的話設備的出膠量會變得不正常甚至會出現花膠的情況出現。
Whether the glue supply line of the double component glue machine is unobstructed and the mixed stick is good. Because we use the glue line colloid characteristics determine very easily Dusseldorf, if you usually do not pay attention to equipment maintenance so great may be blocked and mixed rod damage, if this part of any equipment to produce the adhesive will become normal or even a flower gum situation.
打膠機的供嬌壓力如果不夠的話也是會出現這個問題的,因為打膠機的膠體完全靠氣壓來擠出設備并完美的涂裝在中空玻璃的鋁條中的。如果壓力過小的話也會導致中空玻璃打膠機密封不嚴。所以我們一定要檢測下我們要購買的雙組份打膠機的壓力系統是否正常,是否能夠正常的調節壓力。
If the pressure of the glue machine is not enough, it will also happen if it is not enough, because the colloid of the glue machine is completely extruded by air pressure and applied to the aluminum strip of the hollow glass perfectly. If the pressure is too small, it will also lead to the tight sealing of the insulating glass machine. So we must check whether the pressure system of the double component glue machine we want to purchase is normal, and whether it can regulate the pressure normally.
排查檢測雙組份打膠機的密封圈以及混合器單向閥,這部分如果損壞的話會導致雙組份打膠機的aB組份比例不對,出現混亂!同時密封圈也算是比較容易損壞的所以我們應當重點排查。
Check and check the seal ring and mixer one-way valve of the two component glue machine. If this part is damaged, it will cause the proportion of aB component of the two component glue machine is not correct, there will be confusion. At the same time, the sealing ring is also relatively easy to damage, so we should focus on the investigation.
本文由雙組份打膠機為您提供,我們的網站是:http://www.aabrs.cn我們將以全心全意的熱情為您提供更優質的服務,歡迎您的訪問!
This article is provided by two component glue machine. Our website is: http://www.aabrs.cn, we will provide you with better service with wholehearted enthusiasm, welcome your visit.
- 中空玻璃生產線一天能做多少平方 2024/12/23
- 全自動丁基膠涂布機操作規程 2024/12/14
- 丁基膠涂布機在使用的常見問題 2024/12/13
- 雙組份打膠機如何調整滴膠量? 2024/12/09
- 中空玻璃生產線的磨損如何解決 2024/12/07
- 雙組份打膠機對于打膠工作完成很重要 2024/12/05
- 全自動封膠線的工業自動化設備介紹 2024/12/03
- 玻璃涂布機設備:設備存在的安全隱患 2024/11/25
- 中空玻璃加工設備:玻璃開膠的應急處理措施 2024/11/21
- 中空玻璃生產線:玻璃起霧怎么辦?昌盛為您解決! 2024/11/20