香蕉视频+在线观看+色吧,熟女内射v888av,亚洲av无码专区色爱天堂老鸭,麻豆安全免费网址入口

臥式中空玻璃打膠機配件保養的方法

時間:2018-04-02 來源:http://www.aabrs.cn/ 發布人:昌盛機械

  臥式中空玻璃打膠機Y型過濾器的位置在輔料泵出口處,清洗時將端蓋擰下,用煤油浸泡,用牙刷類刷子刷干凈。安裝時將網放在端蓋里用手擰到底,再用扳手擰緊。用一組膠洗一次,如無雜質兩組膠洗一次,靈活掌握。

  The horizontal Y filter is located at the outlet of the auxiliary pump. When it is cleaned, the cover is screwed down, kerosene soaked and toothbrush brushes clean. The installation will be placed on the end cover by hand net screwed in the end wrench, tighten. Use a group of glue to wash once, if there is no impurity, two groups of glue is washed once, and master it flexibly.

  當膠流速變慢或者混膠不均時清洗混合器。將混合器拆下橫放在臺鉗上,夾住兩端蓋,不要夾到螺絲。用六角扳手松開兩端的六條螺絲,打開器體,取出墊片,擋針,混合芯。將各個零件清洗干凈。

  When the flow rate of the gum slows down or the gum is uneven, the mixer is cleaned. The mixer remove across the vise, clamped at both ends of cover, not to screw clamp. Use six angle wrench to loosen the six screws at both ends, open the body, take out the gasket, stop pin and the mixing core. Clean the parts.

  端蓋不要弄變形,各個平面不要有劃傷。混合器一端有凹槽,安裝時將其放進有擋針孔的一面,將擋針放入擋針孔,橫放在凹槽上。更換好墊片后將端蓋對準器體,A對A,P對P,擰上螺絲,擰好后橫放在臺鉗上夾緊,用扳手擰緊下端的四條螺絲,松開臺鉗,器體旋轉300°,夾緊臺鉗,再擰緊下面四條螺絲。依次擰四五次即可。

雙組份打膠機

  Do not deform the end cover, do not scratch any flat surface. One end of the mixer has grooves. When it is installed, it is placed into the side of the pinhole, and the retaining pin is put in the pinhole and positioned on the groove. After replacing the gasket, the end cover is aimed at the body, A A, P to P, screw up the screw, screwed up on the clamp, tighten the four screws at the lower end with the wrench, loosened the table clamp, the body rotates 300 degrees, clamp the tongs, and tighten the four screws below. Turn four or five times in turn.

  清洗時將其擰下,用尖嘴鉗擰下小螺母,拔出針體,彈簧。全部清洗干凈。針閥出口平面及針帽確保無任何雜質,劃傷,變形。

  When cleaning, unscrew the nut with a small clamp screw, pull out the needle body, spring. Clean up all. The outlet and needle cap of the needle valve ensure no impurities, scratches and deformations.

  臥式中空玻璃打膠機臥式中空玻璃打膠機臥式中空玻璃打膠機大過濾器的位置在高壓表B表右下,擰下回流閥下方膠管,擰下過濾器,將網及網芯取出,彈簧、取出,刷干凈,將彈簧小孔套在網芯的凸點上。倒著裝入器體后轉過來擰在膠機上。用3-5組洗一次,如無雜質,靈活掌握即可 。

  Horizontal hollow glass machine glue machine, horizontal hollow glass beating machine, the horizontal hollow glass rubber beating machine is located at the right of the high pressure meter B, underneath the rubber tube under the backflow valve, screw down the filter, remove the net and net core, spring, remove, brush clean, and put the spring hole on the core of the net. Reverse the loader body and turn it on the glue machine. Use 3-5 groups to wash once, if there is no impurity, we can grasp it flexibly.

  臥式中空玻璃打膠機膠槍的槍口混合器清洗時直接擰下槍口混合器取出混合芯即可。清洗槍柄混合器時,先把槍上的定位螺絲松開,然后擰下槍柄混合器.

  When the muzzle mixer of the rubber gun is used for cleaning the horizontal hollow glass glue machine, the muzzle mixer is directly screwed down and the mixing core is removed. When the first mixer cleaning grips, positioning screws loose on the gun, then unscrew the grips mixer.

  本文的精彩內容來自雙組份打膠機詳細內容請點擊我們的官方網站:http://linshi.jncsjx.com謝謝您的到來!

  The highlights of this article are from two group glue dispenser. Please click on our official website: http://linshi.jncsjx.com, thank you for coming.

聯系我們Contact us

  • 咨詢熱線:0531-85717458 13705446998
  • 公司地址: 山東省德州市齊河安頭鄉企巢工業園
  • 掃碼聯系我們:

截屏,微信識別二維碼

微信號:13705446998

//