丁基膠涂布機溫控表溫度的調整技巧
時間:2018-01-22 來源:http://www.aabrs.cn/ 發布人:昌盛機械
丁基膠涂布機是完成中空玻璃首道密封的必備設備之一,所起到的作用無可替代,所以也是中空玻璃制作廠家必備設備之一,那么我們就談一下它的保養與維修,
Butyl rubber coating machine is one of the necessary equipment to complete the first hollow glass sealing, the irreplaceable role played, so it is one of the necessary equipment of insulating glass production factory, then we will talk about the maintenance and repair,
出膠比不均勻,調節膠頭上的頂絲,二是膠缸不進不退,氣動的考慮是氣動閥卡了(要常加油)液壓的就是液壓站油泵漏氣,或者是油缸內泄漏(壓力升一點馬上降下來)三是膠頭出膠很不勻,一邊粘的很好,另一邊不粘,就是一側加熱棒壞了,或者線頭斷了。
A binder ratio is not uniform, regulating screw plastic head, two is a rubber cylinder irreversible, pneumatic pneumatic valve is considered card (often to refuel) is the hydraulic station hydraulic oil pump leak, or cylinder leakage (pressure rise a little down immediately) three is plastic head the glue is not uniform, while the viscosity is very good, the other side is the side of the heating rod is not sticky, broken, or broken head.
檢查膠缸、膠頭的溫度是否正常,壓力是否在我們設定的范圍之內,檢查兩膠頭的距離是否過大(此距離設定至鋁條剛剛能從兩個打膠頭之間過去為好)。
Check whether the temperature of the rubber cylinder and rubber head is normal, whether the pressure is within our range, and check whether the distance between the two rubber heads is too large (the distance is set to the aluminum strip just to pass from the two rubber heads to the best).
該設備的膠頭加熱和膠缸加熱,由加熱棒兩個和加熱盤一個提供,由溫控表來設定和調整溫度的高低,若發現溫度升不高或升高后往下降,請檢查加熱棒或加熱盤是否損壞,并檢查溫控表是否正常。
The device of glue and glue cylinder head heating heating, a heating rod two and a heating plate, a temperature control table to set and adjust the temperature, if the temperature rise is not high or increased after going down, please check the heating rod or the heating disc is damaged, and check whether the normal temperature table.
該設備全部采用液壓系統,油缸及液壓系統全部采用高壓油管連接,每個連接處都由組合墊密封,若發現漏油,及時更換組合墊。
The device adopts hydraulic system, oil cylinder and hydraulic system are all connected by high pressure oil pipe. Each connection is sealed by combination gasket. If we find oil leakage, replace the combination cushion in time.
皮帶跑偏,調節平衡螺桿。六是膠頭朵堵了,卸下來,用汽油 洗干凈清理臟東西,再安上,以后加膠注意不要沾上臟東西。中空玻璃設備
The belt runs off and regulates the balance screw. Six is glue head plugging, unloaded, clean clean dirty things with gasoline, and then go up, add glue and pay attention not to dirty things later. Hollow glass equipment
本文由雙組份打膠機友情奉獻.更多有關的知識請點擊:http://linshi.jncsjx.com我們將用的技術.真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.
This article is a friendship contribution from two component glue making machine. Please click on more related knowledge: http://linshi.jncsjx.com, we will use the most advanced technology and the most sincere attitude to provide you with the most comprehensive service. We will dedicate more related knowledge to you. Please look forward to it.
- 全自動丁基膠涂布機操作規程 2024/12/14
- 丁基膠涂布機在使用的常見問題 2024/12/13
- 雙組份打膠機如何調整滴膠量? 2024/12/09
- 中空玻璃生產線的磨損如何解決 2024/12/07
- 雙組份打膠機對于打膠工作完成很重要 2024/12/05
- 全自動封膠線的工業自動化設備介紹 2024/12/03
- 玻璃涂布機設備:設備存在的安全隱患 2024/11/25
- 中空玻璃加工設備:玻璃開膠的應急處理措施 2024/11/21
- 中空玻璃生產線:玻璃起霧怎么辦?昌盛為您解決! 2024/11/20
- 中空玻璃加工設備:選擇中空玻璃,創更舒適的環境 2024/11/18