Lubricate both electric motors. The main motor and auxiliary motor of the butyl rubber applicator are equipped with lubricators at the inlet.

當機油低于低端刻線時，應將機油杯取下并重新加注10號機油。 如果沒有注油器，則在滴油或電動機嚴重缺油時，可以拆下主電動機進氣管和電動機之間的帶電連接，并應使用油槍補充油，并使用輔助電動機 可以旋開端蓋螺母以加油。

When the oil level drops below the low end mark, the oil cup should be removed and refilled with No. 10 oil. If there is no oil injector, the live connection between the main motor intake pipe and the motor can be removed in case of oil dripping or severe oil shortage in the motor. An oil gun should be used to replenish the oil, and an auxiliary motor can be used to loosen the end cap nut for refueling.

2.丁基膠打膠機使用一段時間后，主泵，輔助泵和比例泵會從內部泄漏膠水，并流入油杯。 您可以清潔膠水并添加油。 用十字螺絲刀固定住主泵，將兩個泵油碗的下端的圓孔順時針擰緊。 配套的油杯可用扳手擰緊。

2. After using the butyl glue applicator for a period of time, the main pump, auxiliary pump, and proportional pump will leak glue from inside and flow into the oil cup. You can clean the glue and add oil. Fix the main pump with a cross screwdriver and tighten the circular holes at the lower ends of the two pump oil bowls clockwise. The matching oil cup can be tightened with a wrench.

3.用油槍將安全閥注滿安全閥的小孔，以防生銹。

3. Fill the small hole of the safety valve with an oil gun to prevent rusting.

4. Y型過濾器位于輔助泵的出口。 清潔時，擰開端蓋，將其浸入煤油中，然后用牙刷清潔。 安裝時，將網罩放到端蓋中并擰到底，然后用扳手擰緊。 用一套膠水清洗一次，如果沒有雜質，用兩套膠水清洗，控制靈活。

4. The Y-shaped filter is located at the outlet of the auxiliary pump. When cleaning, unscrew the end cap, immerse it in kerosene, and then clean it with a toothbrush. When installing, place the mesh cover in the end cover and tighten it to the bottom, then tighten it with a wrench. Clean once with one set of glue, and if there are no impurities, clean with two sets of glue for flexible control.

5.大型過濾器的位置在高壓儀表B臺的右下角，擰下回油閥下方的軟管，擰下過濾器，取出網和芯，彈簧，取出，用刷子清洗， 并用凸塊上的芯覆蓋彈簧的小孔。 向后旋轉，然后將其擰緊在丁基膠打膠機上。

5. The position of the large filter is in the lower right corner of the high-pressure instrument panel B. Unscrew the hose below the return valve, unscrew the filter, take out the mesh, core, spring, remove it, clean it with a brush, and cover the small hole of the spring with the core on the convex block. Rotate it backwards and then tighten it onto the butyl adhesive applicator.

3-5組洗一次。 如果沒有雜質，則可以靈活控制。

Wash once in 3-5 groups. If there are no impurities, it can be flexibly controlled.

本文由立式丁基膠涂布機整理發布，您是不是對這些內容有所了解了呢?更多的內容請點擊：http://www.aabrs.cn我們會有更多精彩內容等你查看。

This article is organized and published by a vertical butyl adhesive coating machine. Do you have any understanding of these contents? For more information, please click on: http://www.aabrs.cn We will have more exciting content waiting for you to check out.