立式丁基膠涂布機的操作規程有哪些？

　　涂布機的開機前準備：

　　Preparation before starting the coating machine:

　　1、檢查各電氣開關，聯線有無脫落或破損等異常現象；

　　1. Check for any abnormal phenomena such as detachment or damage in the electrical switches and wiring;

　　2、按工藝片路要求在常溫停機狀態下穿好牽引帶；

　　2. Wear the traction belt according to the process route requirements and stop at room temperature;

　　3、啟動排風設備；

　　3. Start the exhaust equipment;

　　4、確認在涂布機房內無任何明火（如電爐等）；

　　4. Confirm that there are no open flames (such as electric furnaces) in the coating room;

　　5、涂布機控制柜和干燥箱體外殼可靠接地。

　　5. The control cabinet of the coating machine and the outer shell of the drying box are reliably grounded.

　　涂布機構兩端裝在涂布機的垂直支撐臂上，通過皮帶、鏈條或電纜的傳動，使涂布機構上下運動，沿絲網的表面涂布。傳動機構連接在伺服或變頻電機上，使其操作平穩，并能夠控制涂布機構的位置。

　　The coating mechanism is installed on the vertical support arm of the coating machine at both ends, and is driven up and down by a belt, chain, or cable to apply along the surface of the wire mesh. The transmission mechanism is connected to a servo or variable frequency motor to ensure smooth operation and control the position of the coating mechanism.

　　自動涂布機的用途：適用于鞋材、電子行業、海棉、EVA、PE、布料等涂膠。

　　The purpose of the automatic coating machine is to apply glue to shoe materials, electronics industry, sponge, EVA, PE, fabrics, etc.

　　1、工藝要求：涂布機需要將膠或者油墨類物質均勻粘連在鋁箔、塑料薄膜或者布料紡織品表面，對涂布工藝要求比較高，不僅要求涂布高度均勻而且要能夠實現高速不停機換卷以提高生產效率；

　　1. Process requirements: The coating machine needs to uniformly adhere adhesive or ink substances to the surface of aluminum foil, plastic film, or fabric textiles. The coating process requires high requirements, not only requiring uniform coating height but also achieving high-speed non-stop roll changing to improve production efficiency;

　　2、方案優點：由變頻器完成各級張力控制，使用張力傳感器實現張力控制，系統簡單且穩定。用PLC或同步控制器來控制驅動輥變頻器速度，同時作為其他變頻器的線速度信號；S350閉環張力控制（有感矢量控制）輕松實現加減速過程中的張力恒定，節省安裝張力；輥的空間，降低機械成本，同時控制確保了涂布效果高度均勻。雙工位收放卷具有預驅動功能，可滿足高速不停機自動換卷、提高生產效率的需求。同時準確的收卷控制可以避免菜心式不良收卷，使收卷效果更好。

　　2. Advantages of the solution: The tension control at all levels is completed by the frequency converter, and the tension control is achieved using a tension sensor. The system is simple and stable. Use PLC or synchronous controller to control the speed of the drive roller frequency converter, while serving as the linear speed signal for other frequency converters; S350 closed-loop tension control (inductive vector control) easily achieves constant tension during acceleration and deceleration, saving installation tension; The space of the rollers reduces mechanical costs, while controlling to ensure a highly uniform coating effect. The dual station winding and unwinding system has a pre drive function, which can meet the needs of high-speed automatic roll changing without stopping the machine and improve production efficiency. Accurate winding control can avoid poor winding of vegetable hearts and improve the winding effect.